Black & Decker BDCMTTS Bedienerhandbuch PDF herunterladen (Seite 3)

the blade is in motion or kickback may occur. Investigate and take corrective actions to

eliminate the cause of blade binding.

c) When restarting a saw in the workpiece, center the saw blade in the kerf and check

that saw teeth are not engaged into the material. If saw blade is binding, it may walk up

or kickback from the workpiece as the saw is restarted.

d) Support large panels to minimize the risk of blade pinching and kickback. Large

panels tend to sag under their own weight. Supports must be placed under the panel on

both sides, near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be tight and secure before

making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.

g) Use extra caution when sawing into existing walls or other blind areas. The protruding

blade may cut objects that can cause kickback.

LOWER GUARD SAFETY INSTRUCTIONS

a) Check lower guard for proper closing before each use. Do not operate the saw if lower

guard does not move freely and close instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and make sure it moves freely and does not touch

the blade or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the guard and the spring are not

operating properly, they must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

c) Lower guard should be retracted manually only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard by retracting handle and as soon as blade

enters the material, the lower guard must be released. For all other sawing, the lower guard

should operate automatically.

d) Always observe that the lower guard is covering the blade before placing saw down

on bench or oor. An unprotected, coasting blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch

is released.

ADDITIONAL SAFETY INSTRUCTIONS

Use clamps or another practical way to secure and support the workpiece to a stable

platform.



Keep your body positioned to either side of the blade, but not in line with the saw

blade. KICKBACK could cause the saw to jump backwards (see Causes and Operator

Prevention of Kickback and KICKBACK).

Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

Always make sure nothing interferes with the movement of the lower blade guard.

Accessories must be rated for at least the speed recommended on the tool warning

label. Wheels and other accessories running over rated speed can y apart and cause

injury. Accessory ratings must always be above tool speed as shown on tool nameplate.

Always make sure the saw is clean before using.

Stop using this saw and have it properly serviced if any unusual noise or abnormal operation

occurs.

Always be sure all components are mounted properly and securely before using tool.

Always handle the saw blade with care when mounting or removing it or when removing the

diamond knockout.

Always wait until the motor has reached full speed before starting a cut.

Always keep handles dry, clean and free of oil and grease. Hold the tool rmly with both

hands when in use.

Always be alert at all times, especially during repetitive, monotonous operations. Always be

sure of position of your hands relative to the blade.

Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/or heavy.

Serious personal injury may result.

Replace or repair damaged cords. Make sure your extension cord is in good condition. Use

only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole receptacles

that accept the tool’s plug.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. 

1 2 3 4 5 6 7 8 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Black & Decker BDCMTTS Bedienerhandbuch Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kreissägen Black & Decker BDCMTTS