Black-decker 3803-10 Bedienungsanleitung PDF herunterladen

MAINTENANCE (Unplug Chain Saw)

1. Keep chain sharp and tensioned correctly.

2. Turn bar over periodically (5 hours use) to ensure even wear on topand bottom rails.

3. Clean accumulated sawdust and oil from passages at the base of the bar, to ensure

proper lubrication of chain and bar groove.

4. Do not use fluids or cleaning agents to clean the saw. Excessive moisture can cause

a short-circuit. Strong cleaning agents and solvents such as kerosene and gasoline

can attach the plastic housings. Wipe the saw clean with rags and use a small brush

to clean the motor cooling air inlet and exhaust slots,

5. The chain saw uses self-lubricating bearings and relubrication is not required.

However, after two seasons of use we recommend a thorough cleaning and

inspection at a Black & Decker Service Center.

6. If the Chain Saw fails to operate, disconnect extension cord from power source first,^

and then from the chain saw. Check service panel for blown fuse or tripped circuit

breaker and examine the extension cord for damage. If chain saw still will not operate,

do not attempt to repair it yourself, take it to a Black & Decker Service Center

for repair.

ACCESSORIES

Use of other than specified accessories may be hazardous.

Model

3801-10

14"

3802-10

16"

3803-10

Guide Bar

38000

38001

38002

Saw Chain 38003

38004

38005

File

38006

38006 38006

File Guide

38007 38007

38007

IMPORTANT

To ensure product safety and reliability, repairs, maintenance and adjustment (other

than those described in the mianual) should be performed by B & D Authorized Service

Centers or other qualified service organizations. Always use B & D replacement parts.

Note: Use only the correct length of bar and chain types as replacements (See

nameplate). An increase in length may overload and damage the motor.

COMMERCIAL/INDUSTRIAL USE WARRANTY

Black & Decker warrants this product for one year from date of purchase. We will repair

without charge, any defects due to faulty material or workmanship. Please return the

complete unit, transportation prepaid, to any Black & Decker Service Center or

Authorized Service Station listed under ‘Tools Electric" in the yellow pages. This

warranty does not apply to accessories or damage caused where repairs have been

made or attemped by others.

MOTOR

Your Black and Decker tool is powered by a B&D-built motor. Be sure your power supply

agrees with nameplate marking. Volts 50/60 Hz means Aiternatiiig Cyrrentiy ONLY, Volts

DC“60 Hi means it will also operate on Direet Current, Voltage decrease of more than 10%

will cause loss of power and over-heating. All B&D tools are factory-tested; if this tool does not

operate, check the power supply,

DO NOT CONNECT TOOL TO DC POWER SUPPLY

Form No. 237595

BLACK & DECKER (U.S.) INC.

INDUSTRIAL/CONSTRUCTION DIVISION

626 HANOVER PIKE, HAMPSTEAD, MD 21074 U.S.A,

Eieistrie ©ihiiiic Sm:

Model 3801-10 - 12" Electric Chain Saw

Model 3802-10 - 14" Electric Chain Saw

Model 3803-10 - 16" Electric Chain Saw

IMPORTANT

BEFORE YOU PLUG IN YOUR BLACK & BECKER ELECTRIC CHAIN SAW...

(Motor will not run if brake engaged.)

Black & Decker Electric Chain Saws are Double-Insulated for added protec

tion against electric shock. This also eliminates the need for a 3 prong

grounding plug.

omima

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

MAINTENANCE (Unplug Chain Saw)1. Keep chain sharp and tensioned correctly.2. Turn bar over periodically (5 hours use) to ensure even wear on topand b

Seite 2 - READ ALL INSTRUCTIONS

WARNING; When using Electric Tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock,

Seite 3 - CHAIN SAW NAMES & TERM!

1. Before using chain saw, review the Safety instructions listed in this Manual and be aware of local regulations covering the operation of your

Seite 4

EXTENSION CORDSDouble insuitated toote have 2 wire cords, and can be used with 2 wire or 3 wire extension cords. Only round jacketed extension

Seite 5 - SAWING PRECAUTIONS

The delivery of oil to the bar and chain is preset at the factory, and for normal use is unlikely to need altering. If adjustment is

Seite 6 - CHAIN BRAKE MAINTENANCE

TO AVOID KICKBACK© Hold the chain saw firmly with both hands.® Don’t overreach.© Prevent the nose of the guide bar (FIG. 5) from contacting a log, bra

Seite 7 - SAVE THESE INSTRUCTIONS

CHAIN BRAKE OPERATIONThe brake is actuated if pressure is applied against the lever when, as in the event of “kickback,” the operator’s hand

Seite 8 - CHAIN BRAKE AND HANDGUARD

ENSURE ADJUSTER NUT IS POSITIONED at the rear of the slot.HOLD THE CHAIN SNUGLY on the guide bar with one hand (FIG, 12).WITH THE GUIDE BAR AT A

Verwandte Modelle: 3802-10 | 3801-10 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Black-decker 3803-10 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Benzinwerkzeug Black-decker 3803-10 herunter. Black & Decker 3803-10 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 3802-10 | 3801-10 |

Kommentare zu diesen Handbüchern